Avision AV36 Manual do Utilizador

Mobile Scanner User’s Manual Regulatory model: FL-0914S Avision Inc.

2.1.1 Installing the Scanner Driver 1. Place the supplied CD-ROM onto your CD-ROM drive. 2. The software installation graphic appears. If not,

• Install Adobe Reader: To view the user’s manuals for the scanner and Button Manager, you need to use Adobe Reader to open and view the manuals in

2-4 2. The computer should detect a new USB device and prompt a “New Hardware Found” message. 3. In Windows 2000, confirms that the “Search for a

3. Completing Your First Scan 3.1 Placing Your Document 3.1.1 Notice on Using the ADF Before using the ADF, please make sure that your paper

3.1.2 Loading Paper to the Paper Feed Slot The scanner is a duplex scanner, which means it can scan one side of the page or both sides of the pa

3.1.3 Loading A Card to the Paper Feed Slot 1. Place the card face up with the long dimension parallel to the paper feed slot and make sure the

3.2 Verifying Your Scanner Installation To verify if your scanner installation is correct, Avision provides you a useful test program called Avisi

Fit Page Actual Size Save File Path File Format Setup Scan 3. Choose your desired file format from the File Format drop down list b

Image Selection Box 6. From the Image Selection Box, choose your desired image type for your scanned image. (Default is Front B&W) If you

Status Bar Fit Page View Thumbnail View 11. You can view the scanned image in Fit Page () or Actual Size (100%) button () from the Viewing too

Trademarks Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows and MS-DOS are trademarks of Microsoft Corporation. IBM, IBM

3.2 A Glance of the Scanner Properties Dialog Box 1 2 3 4 5 6 7 8 1. Tab Options Choice: Image, Compression, Color Dropout, Paper, Options,

3-9 3.3 Scan from the scanner button To scan using the scanner buttons, follow these steps: 1. Load the originals. 2. Press the Scan button to

4. Using the Scanner Properties Dialog Box The Scanner Properties dialog box allows you to configure the scanner’s settings. It consists of seve

4.1 Buttons on the Scanner Properties Dialog Box The buttons on the Scanner Properties dialog box Buttons Description Defaults Click the Defaul

The following table shows the default settings： Tab name Default settings Image Image：Front B&W Binarization：Dynamic Threshold Resolution：2

4.2 The Image Tab The Image tab allows you to choose the front side and (or) the rear side of your document, the type of image, and to set several

4.2.1 The Image Selection Box The Image Selection box includes the image type and document side option. If you wish to scan both the front side a

Example 2：Scanning a two-sided color document, one in B&W(Drop Blue Color：Threshold：10, Background：79), the other in color Side/Image Selecti

Front/Rear Auto Color Detection: Click to automatically detect and scan the front or the rear page of your color document in color image mode. If

4.2.2 Other Image Options Binarization This is the process of converting a grayscale or color image to a bi-tonal image. There are several different

FCC Radio Frequency Interference Statement This product has been tested and found to comply with the limits for a class B digital device, pursuant

Fixed Processing: Used for black-and-white and other high contrast documents. A single level is set to determine the black-and-white transition

Error Diffusion Image 4-10

Threshold Used to convert a grayscale image to a bi-tonal image. The value ranges from 0 to 255. A low threshold value produces a lighter image,

Gray Document Type: Choice: Normal, Photo, Document Three options of document type are provided when you choose Gray as the image type for you

Normal Photo Document (Threshold: 230) Normal Photo Document (Threshold: 230) 4-13

Brightness Adjusts the lightness or darkness of an image. The higher the value, the brighter the image. Drag the slider to the right or left to

Resolution A good control of the resolution results a good detail of an image that scans. The resolution is measured by dots per inch (dpi). Nor

Invert Reverses the brightness and the colors in the image. The default setting is Black on a White background. Reverse mode is White on a Blac

Scan Source Choice: y Auto Document Feeder: Used to scan multiple pages. y Flatbed: Used to scan a single page. For example, pages from newspap

Color Matching The purpose of Color Matching is getting the accurate color. This option uses the default parameters (ICC profile) to adjust the c

Disposal of Waste Equipment This symbol on the product or on its packaging indicates that the product can not be disposed of with your other hous

4.2.4 Scanning grayscale images The following options are available for scanning gray images. y Brightness y Contrast y Resolution y Invert

4.2.6 Editing Profiles The Scanner Properties dialog box allows you to change and save your frequently used scan settings into a profile. You can

To load a profile, 1. From the Image tab dialog box, choose your favorable profile from the “Profiles” dropdown list box. 2. Your favorable p

To rename a profile, 1. From the Image tab dialog box, click “Profiles” to prompt the Edit Your Profile dialog box. 2. Choose the profile you

4.3 The Compression Tab The Compression tab allows you to compress your scanned image and choose the level of compression. Bi-tonal images are nor

The Compression tab dialog box 4-24

4.4 The Color Dropout Tab 4.4.1 Color Dropout Selection Color Dropout tab allows you to drop either of the red, blue, or green color in your sca

The Color Dropout dialog box 4-26

4.4.2 Other Color Dropout Options Advanced Processing provides two options that can adjust your scanned image in the best optimal result. Filter

Remove Blue, Threshold: 20, Background: 255 Remove Blue, Threshold: 20, Background Level: 210 4-28

System Requirements ¾ IBM compatible PC 586, Pentium or higher ¾ Microsoft Windows 2000, Windows XP, Windows Vista, Windows 7 ¾ USB port 2.0 (c

4.5 The Paper Tab The Paper tab allows you to define values relating to image output (i.e., Auto Crop or not, Scan Area, OverScan, Multi-Feed Dete

4.5.1 Cropping Cropping allows you to capture a portion of the document being scanned. Choice: Automatic, Fixed to Transport, EOP (End of Page)

Automatic Multiple This option allows you to place various sized documents such as photos, ID Cards, or business cards on the flatbed (if availabl

4.5.2 Other Paper Selection Deskew Use this option to automatically deskew a document. Note: If the skew angle is too great, some of the image

Choose “Unknown Length” if you have a batch of long page document with unknown length. Choose “Enter Length” to enter the length and width of your

Note: 1 Within the specified timeout period, if you load your document to the feeder, the scanner starts scanning automatically. 2 If your scan

4.6 The Multi-Feed Detection Tab Multi-Feed Detection Multi-Feed Detection allows you to detect overlapped document that go through the auto do

Additional Length Detection Additional Length Detection allows you to define the length of document being multi-fed. This value indicates the addi

By Length+Position: When a multi-feed is detected for the first time, the scanner memorizes the length and position of the paper attached to the do

Detection Area This option allows you to specify a multi-feed detection area. To specify a multi-feed detection area, 1. Choose Disable from the I

Table of Contents 1. Introduction...1-1 2. Scanner Installation...2-1 2.

Detection Area: Outside the Range, Box, Top: 3”, Bottom: 7” 4-39

Ultrasonic Detection Ultrasonic Detection allows you to set overlapped document by detecting paper thickness between documents. Note： The availa

Clear the Multi-Fed Paper: Choice: Manual, Auto If Auto is selected, once multi-feed is detected and scanning operation is stopped, the scanner w

How to add the sound alarm： 1. Click the Browse button on the right side of the speaker icon. The Open dialog box appears. 2. Choose your wave f

4.6.1 Relative to Document Relative to Document: (used for batches of same-sized documents) This option allows you to crop different areas on your

3. Click the Preview tab to display the Preview window. A black rectangular box appears to indicate the max. scan size your have just selected. T

A Cross Sign The Relative Area 7. Check the B&W image from the Image Selection box to scan the entire document. 8. Click the Sc

4.7 The Preview Tab The Preview tab allows you to preview (a low-resolution scan) your image before final scan. This preview image lets you alloc

4.8 The Options Tab The Options tab allows you to set following additional image processing settings. The Option tab dialog box 4-47

Flip Side Rotation Select “fanfold” to rotate the image of the reverse side to 180 degrees. This is applied to double-sided document which are v

vii 4.7 The Preview Tab ... 4-46 4.8 The Options Tab... 4-47 4.9 The Set

Rotate Image Choose the rotation angle from the drop down list if you wish to rotate your scanned image. Choice: None, 90°CW(clockwise), 90°CCW(co

Blank Page Removal Check if you wish to remove the blank page and move the slider to the left or right to your desired threshold. Edge Fill Ch

Image Control Option Check the Mirror box if you wish to reverse the right and left side of your image. Original The Mirror Effect 4-5

Despeckle Occasionally small dots or specks appear in the background of a scanned image. Remove unwanted speckles provides a cleaner image for OCR

Note: • The function is currently available for Black and White image only. • To scan at rated speed, it is recommended to set the noise radius

Background Setting This option allows you to set your scan background. Choice: White Background, Black Background. White Background Black Ba

4.9 The Setting Tab The Setting tab allows you to set the following settings: The Setting tab dialog box Energy Saving Control Check the Enabl

Cache Mode: None, Page Number, Memory Size. This option allows you to assign a specified memory size from the available RAM to process the imag

Show Scanning Progress Check and the scanning progress bar will be shown during scanning. Show Warning Message Check to show the warning messages

4.10 The Imprinter Tab The Imprinter tab allows you to print alphanumeric characters, date, time, document count and custom message on your scanne

1-11. Introduction Congratulations on your purchase of the color image scanner. With this scanner, you can scan documents at a fast rate to inc

Contents Print All Check Print All to automatically print the text at all pages of your documents. Uncheck Print All to print the text for the fi

String Orientation Choice: Normal, Rotated (180 degrees) Delay Choose the position of the print string. Move the slider from 1 to 5000. Default

4.11 The Information Tab The Information tab displays the following system and scanner information. The Information tab dialog box The “Repor

4-62 The “Reset Pad Count” button： After scanning approximately 50,000 pages (the number varies based on type of scanner) through the Auto Documen

5. The ISIS Interface Operation The ISIS driver operation method is similar to the TWAIN’s functions on the ISIS interface screen is briefly descr

6. Using the Buttons To use the buttons on the scanner, you need to install the Button Manager. To ensure the Button Manager work properly, plea

This indicates the scanner model 6-2 The Function Icon (The number of function icons vary based on type of scanner.) The Button IconThe Button Pan

The default setting is indicated in highlighted color. If you wish to change the setting, use this window to reset the setting for the file format,

6-4 Note: To accurately use the default settings, you need to install the necessary software application such as E-mail software or Adobe Reader bef

7. Care and Maintenance 7.1 Cleaning the Scanner Glass Use the included cleaning cloth to clean the rollers and the scanner glass on the follo

2. Scanner Installation Precautions  Keep the scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause damage

7-2 Caution: Wait two minutes for the components to dry before proceeding to the next step. 5. Place one sheet of paper in the scanner. Scan

8. Troubleshooting 8.1 Clearing a Paper Jam In the event of a paper jam, follow the procedures below to remove the paper: To clear a paper jam:

8-2 Question: Feeding paper from the ADF easily causes paper jam. Answer: Make sure to close the front paper tray. While the front paper tray is

9. Specifications All specifications are subject to change without notice. Model Number FL-0914S Scanner Type Duplex scanner Light source LE

Index Remove Red, Remove Green, Remove Blue, Custom, 4-25 Ａ Color Matching, 4-18 Additional Length Detection, 4-36 Contrast, 4-14 Cropping Auto Colo

bGray, 4-6, 4-12 Ｉ Intelligent Mode (Skip Multi-feeds) Disable, By Length, By Position, By Length+Position, 4-36 Invert, 4-16 Ｊ JPEG, 4-23 Ｍ Mirror,